DC 5V 12V 24V Delay Turn On/off Timing Cycle Timer Relay Signal Trigger Switch

Description

Welcome to Happy_guy
You may also like, welcome use "Add to basket to buy"
Description
Welcome to our store:
DIY_happy
Tips:
If you need Large quantity, please contact us, we can wholesales.
Specification
:
I
nstructions for use:
Setting of working parameters:
Hold down the SET button without letting go, the display will show P-XX after 0.5 seconds, press ▲ and ▼ to change the working mode. After selecting the working mode, short press the SET key to enter the A time setting, the screen displays Axxx, press the ▲ and ▼ keys to modify the A time parameter, press the ↑ and ↓ keys shortly to add or subtract 1, long press to quickly add or subtract 10, press The S key can set the position of the decimal point. After setting the A time, press the SET button to set the B time, the screen displays bxxx, press the ▲ and ▼ keys to modify the B time parameter, press the ▲ and ▼ keys to shortly press to add or subtract 1, long press to quickly add or subtract 10. Press the S4 key to set the position of the decimal point. After setting the B time, press the SET button again to enter CXXX, press the SET button again to enter dXXX, and press the SET button again to exit the setting state and save all parameters.
The above settings such as B time or other time has no effect, no need to set, press SET to skip.
The meaning of the decimal point position:
Ax.xx The decimal point is in hundreds, and the time range is 0.01~9.99 seconds
Axx.x The decimal point is in the tenth place, and the time range is 0.1~99.9 seconds
Axxx. The decimal point is in the ones place, and the time range is 1~999 seconds
Axxx has no decimal point, the time range is 1~999 minutes
Turn off the display: In the non-setting state, press the S key to turn off the display, and then press it again to turn it on again.
Operating mode
P-00: Invalid (skip)
P-01: The relay is disconnected after power-on or triggered, and the relay is closed after a delay of time A
P-02: Closed after power-on or triggered, the relay is disconnected after a delay of time A
P-03: Jog mode, pull-in with signal, disconnect without signal
P-04: Self-locking mode, the relay state flips once after each trigger
P-05: After triggering, the relay pulls in, and stops after a delay of A time. Repeated triggering is not allowed during the delay
P-06: After triggering, the relay is closed, and it will stop after a delay of A time. The trigger will be repeated during the delay and the timing will be restarted.
P-07: After triggering, the relay is closed, and it will stop after a delay of A second. Repeated triggering during the delay period, the time will accumulate
P-08: After triggering, the relay is closed, and it will stop after a delay of A second, and it will stop immediately after triggering again during the delay.
P-09: After triggering, the relay is closed. After the signal disappears, it will delay for A second to stop, and the trigger will restart during the delay.
P-10: After power-on, pull-in time A, disconnect time B, infinite loop
P-11: When there is a continuous signal, pull in A time, disconnect B time, infinite loop, stop immediately after the signal disappears
P-12: Trigger once, pull in A time, disconnect B time, infinite loop, trigger again to stop
P-13: The relay is switched on when the power is on, the relay is disconnected after triggering, and the relay is switched on after the delay time A
P-14: There is a continuous signal, the relay is closed after the time A exceeds, and the signal disappears and the relay is disconnected
P-15: The relay with continuous signal is disconnected, and the relay is closed after the signal disappears for more than A time
P-16: When there is a continuous signal for more than A time, the relay is closed, and after the signal disappears for more than A time, the relay is disconnected
P-17: The relay is closed after a continuous signal exceeds the time A, and after the signal disappears, the relay is disconnected after the continuous signal exceeds the time A again
P-18: Trigger, the relay will be closed after time A is exceeded, and triggered again, the relay will be disconnected after time A is exceeded
P-19: There is a continuous signal that the relay pulls in for A time and then stops, and then if the signal disappears, the relay pulls in for A time and then stops
P-20: There is a pulse signal (rising edge or falling edge), the relay stops, and there is no pulse signal, the relay pulls in after a delay of A time [continuous high level or continuous low level is considered as no pulse]
P-21: After power-on, the relay will be closed after the delay time A, and stop after the time B is closed
P-22: After triggering, the relay will be closed after delaying time A, and stop after closing time B
P-23: There is a continuous signal and the relay is closed after the time A is exceeded, and it stops after the time B is closed
P-24: After triggering, the relay stops after A time, and then counts B time after it stops. It cannot be triggered again within A+B time
P-25: After triggering, the relay stops after closing A time, timing B time, and then closing A time and then stop. During this time, it cannot be triggered repeatedly
P-26: Counting mode, rising edge trigger, every time a rising edge is detected, the value is +1, the maximum count is 9999, the maximum frequency is 20Hz, short press the S1 key to clear
P-27: Counting mode, falling edge trigger, each time a falling edge is detected, the value is +1, the maximum count is 9999, the maximum frequency is 20Hz, short press the S1 key to clear
P-28: Counting mode, rising edge trigger value +1, maximum 9999, MAX 20Hz, when the count value is equal to the d parameter, the relay is closed and the program stops. Short press S1 button at any time to reset
P-29: Counting mode, rising edge trigger value +1, maximum 9999, MAX 20Hz, when the count value is equal to parameter d, the program will automatically reset after the relay pulls in for A time. Short press S1 button at any time to reset
P-30: After the trigger, delay time A and then pull in (falling edge trigger), pull in after B time, disconnect, count once, stop when the number of counts reaches the d parameter, if there is a trigger (rising) during the A time delay Edge) will reset
P-31: After power-on, it will count down the time c and then automatically trigger. After the trigger, it will be closed after a delay of time A, and disconnected after the time of pull-in B. It will count once, and a new cycle will be restarted when the number of counts reaches the d parameter.
Package Include:
Relay Switch x 1pcs
Payment
We only accept payment via Paypal.
The buyer is responsible for any applicable import duties and local taxes.
Usually there's no any charges for small parcel. But please verify with your customs before making your purchase.
Delivery details
The items will be shipped within 1~2 working days after your payment is received and cleared.(excluding Saturday, Sunday & Holiday)
All items will be shipped to your Paypal address, so please make sure to provide us with the correct, precise, detailed shipping address.
The Delivered time to USA buyer is about 7~20 days, other country about
15~35
days delivered.
Notes: pls contact us if you need need trackable or express shipping service.
Terms of sales
All the items will be tested before shipping. Buy them with the confidence!
We maintain the excellent service standards
and strive for 100% customer satisfaction and
Positive feedback.
If you have any problem, please do feel free to contact us before leave Neutral
or Negative
feedback, so that we can satisfactorily address your concerns.
Return
We afford all cost if it's our fault. Exchange or refund.
Contact us
We strive to provide you with the best service, reply your question within 24 hours.
Business time:
9:30~21:30 (GMT+8)
exclude the weekend and holidays.
Contact us